Table of Contents
Table of Contents
NOTE: Some values are only shown if the applicable machine configuration is detected or a valid calibration has been completed.
NOTE: Except for instantaneous values, all values displayed are since last reset.
The system considers work recording to be on when the coverage map begins painting. See equipment setup / recording source help for more information.
Some machine or implement control units define the working width that is used for area measurements. Configure the machine or implement for accurate values.
|
If the working width is not defined by a control unit, use the Edit Width button to change the working width. |
|
Go to Equipment Manager to define a new or select an existing machine or implement. See Machine Profile and Implement Profile help for more information.
|
Area Worked - The total area that was worked while work recording was on. |
|
|
Time Worked - The total time that work recording has been on. |
|
|
Productivity - The current area worked averaged over time. |
|
|
Fuel Usage - The total amount of fuel used. |
|
|
Fuel per Area - The current fuel consumption averaged over area worked. |
|
|
Fuel per Hour - The current fuel consumption averaged over time. |
|
|
Working Speed - The average speed while work recording is on. |
|
|
Elapsed Engine Hours - The total time the engine has been running. |
|
|
Idle Time - The total time the engine has been idling. |
|
|
Distance - The distance the machine has traveled. |
|
NOTE: Combines without yield monitoring systems do not display moisture, wet yield, dry yield, total wet volume, total dry volume, throughput, total wet weight, and total dry weight.
|
Moisture - The average moisture of the harvested crop. |
|
|
Wet Yield - The average wet yield over the area worked. |
|
|
Dry Yield - The average yield over the area worked after taking into consideration the standard moisture for the crop. |
|
|
Total Wet Volume - The total wet volume of the harvested crop. |
|
|
Total Dry Volume - The total volume of the harvested crop after taking into consideration the standard moisture for the crop. |
|
|
Throughput - A measurement of the machine mass productivity measured over time. |
|
|
Total Wet Weight - The total wet weight of the harvested crop. |
|
|
Total Dry Weight - The total weight of the harvested crop after taking into consideration the standard moisture for the crop. |
|
|
Elapsed Separator Hours - The accumulated time the separator has been engaged. This value resets to zero when the machine is powered off. |
|
|
Elapsed Header Hours - The accumulated time the header has been engaged. This value resets to zero when the machine is powered off. |
|
NOTE: If a dry spreader has multiple bins, values for each bin are displayed separately.
|
Mass Applied - The total weight of product applied for the selected product. |
|
|
Mass per Area - The total product applied over the area worked. |
|
|
Mass per Hour - The total weight of product applied over time. |
|
|
Moisture - The average moisture of the harvested crop. |
|
|
Wet Yield - The average wet yield over the area worked. |
|
|
Dry Yield - The average yield over the area worked after taking into consideration the standard moisture for the crop. |
|
|
Throughput - A measurement of the machine mass productivity measured over time. |
|
|
Total Wet Weight - The total wet weight of the harvested crop. |
|
|
Total Dry Weight - The total weight of the harvested crop after taking into consideration the standard moisture for the crop. |
|
|
Dry Matter - The average dry material of the harvested crop. |
|
|
Length of Cut - The height of the cutting edge of the header. |
|
|
Inoculant High / Low - A measurement of forage additives used to cause, manipulate, or enhance the fermentation process of harvested material. |
|
|
Constituent - A measurement of material within the harvested crop, such as starches, crude protein, or sugar. A separate value is listed for each constituent. |
|
|
Round Module Count - The total number of completed round modules. |
|
|
Round Module Moisture - The average moisture of the module currently in the module builder. |
|
|
Round Module Weight - The weight of the module currently in the module builder. |
|
|
Moisture - The average moisture of the harvested cotton. |
|
|
Instant Moisture - The current moisture reading from the moisture sensor. |
|
|
Seed Cotton Yield - The average number of seed cotton bales over the area worked. |
 |
|
Lint Yield - The average number of lint bales over the area worked. |
|
|
Crop Yield - The average yield over the area worked. |
|
|
Elevator Trash - The percentage of waste material included in the harvested crop. |
|
|
Throughput - A measurement of the machine mass productivity measured over time. |
|
|
Total Weight - The total weight of the harvested crop. |
|
|
Fuel Efficiency - The weight of the harvested crop per fuel consumed. |
|
|
Primary Cleaning Losses - The amount of cleaning losses over the area worked. |
|
|
Machine Usage Total - The total utilization hours of the machine. The total is the sum of the Working, Unproductive, and Idle hours. |
|
|
Working - Harvesting - The machine utilization hours while harvesting crop. |
|
|
Working - Crop Missing - The machine utilization hours with header active and not harvesting crop. |
|
|
Working - Unloading Only - The machine utilization hours unloading harvested crop while in neutral. |
|
|
Unproductive - Feed Reversed - The machine utilization hours with the chopper blades in reverse. |
|
|
Unproductive - Maneuvering - The machine utilization hours driving in field without harvesting crop. |
|
|
Unproductive - Transporting - The machine utilization hours with the machine in transport. |
|
|
Machine Usage - Idle - The machine utilization hours with the machine idle. |
|
|
Elapsed Elevator Hours - The accumulated time the elevator has been engaged. |
|
|
Elapsed Height Control Hours - The accumulated time the height control has been engaged. |
|
|
Elapsed Divider Hours - The accumulated time the divider has been engaged. |
|
NOTE: If a sprayer has multiple tanks, values for each tank are displayed separately.
NOTE: If See & Spray detects a low percentage of targets, then the amount of product applied should also be low.
|
Area Worked - The area that the boom has passed over while work recording is on. |
|
|
Area Applied - The area that is actually sprayed with product. |
|
|
Percent Applied - The area applied divided by the area worked. |
 |
|
Time Worked - The amount of time elapsed with work recording on. |
|
|
Productivity - The area that the boom has passed over while work recording was on over time. |
|
|
Volume Applied - The total amount of all products and tank mixes applied using any spray mode. |
|
|
Volume per Area - The amount of product applied over the area applied. |
|
|
Volume per Hour - The amount of product applied over time. |
|
|
Average Weed Pressure - The percentage of vegetation coverage by plants that See & Spray identifies as weeds. |
|
|
Nitrogen - The mass weight of nitrogen applied per unit area. |
|
|
Nitrogen Concentration - The mass weight of nitrogen applied per volume of liquid manure. |
|
|
Ammonium - The mass weight of ammonium applied per unit area. |
|
|
Ammonium Concentration - The mass weight of ammonium applied per volume of liquid manure. |
|
|
Phosphorus - The mass weight of phosphorus applied per unit area. |
|
|
Phosphorus Concentration - The mass weight of phosphorus applied per volume of liquid manure. |
|
|
Potassium - The mass weight of potassium applied per unit area. |
|
|
Potassium Concentration - The mass weight of potassium applied per volume of liquid manure. |
|
|
Dry Matter - The percentage of manure slurry that is dry matter. |
|
|
Volume - The volume of manure slurry that is applied over the Area Worked. |
|
|
Total Volume - The total volume of manure slurry that has been applied for the current job. |
|
|
Area Worked is the total area that was worked while work recording was on. The calculation is based on working width, ground speed, and time worked. It counts up when work recording is on. |
|
Instant Instant Productivity is the current area worked averaged over time. If the machine works 1 hour under current conditions, it would work this area. The calculation is based on current speed and working width. If the machine is moving slower than 0.1 km/h (0.06 mph) or one of the values is not available, dashes are shown. Instant Productivity is zero when work recording is off. Average Average Productivity is the area worked divided by elapsed engine hours. Productivity over the entire operation, including turning, filling, and road transport, is recorded. For example, turning in headlands with work recording off or filling a sprayer causes Average Productivity to decrease while Instant Productivity shows zero. |
|
Instant Instant Fuel per Area is the current fuel consumption averaged over area worked each second. If the machine works one hectare / acre under current conditions, it would burn exactly this amount of fuel. Calculation is based on current fuel consumption, current speed, and working width. If the machine is moving slower than 0.1 km/h (0.06 mph) or one of these values is not available, dashes are shown. Instant Fuel per Area is zero when work recording is off. Average Average Fuel per Area displays the total fuel usage divided by area worked. Average fuel consumption over the entire operation, including turning, filling, and road travel, is recorded. For example, turning in headlands with work recording off or filling a sprayer causes Average Fuel per Area to increase while Instant Fuel per Area shows zero. |
|
Instant Instant Fuel per Hour is the current fuel consumption averaged over time. If the machine runs under current conditions for 1 hour, it would burn exactly this amount of fuel. Average Average Fuel per Hour is fuel usage divided by elapsed engine hours. |
|
Idle Time is the total time the engine has been idling. The engine is considered idling if the engine is running, machine is not moving, SCVs are not extending or retracting, and the PTO is turned off. |
|
Distance totals the distance the machine has traveled. Regardless of recording state or direction of travel, Distance counts up as long as the machine is moving. When a distance of 99 999 meters or feet is reached, the counter starts counting up from zero again. |
|
Instant Instant Yield is current amount of harvested crop averaged over the area worked. If the machine works one hectare / acre under current conditions, it would harvest this amount of crop. Calculation is based on current yield measurement, current speed, and working width. If machine is moving slower than 0.1 km/h (0.06 mph) or one of the values is not available, dashes are shown. Instant Yield is zero when work recording is off. Average Average Yield is the total amount of harvested crop divided by the area worked. Yield over the entire operation, including turning, unloading, and road transport, is recorded. For example, turning in headlands with work recording off causes Average Yield to decrease while Instant Yield shows zero. |
|
Instant Instant Elevator Trash is the current percent of waste material passing through the elevator. Instant Elevator Trash is zero when work recording is off. Average Average Elevator Trash is the average percentage of waste material. |
|
Area Worked is the area that the boom has passed over while work recording is on. With See & Spray, this includes when spray method is either See & Spray or broadcast mode. |
|
Area Applied is the area that was actually sprayed with product. With See & Spray, unsprayed area does not count toward Area Applied. |
|
Instant Instant Nitrogen is the instantaneous mass weight of nitrogen applied per acre (or hectare) for the selected field. Average Average Nitrogen is the average mass weight of nitrogen applied per acre (or hectare) for the selected field. |
|
Instant Instant Nitrogen Concentration is the instantaneous mass weight of nitrogen applied per volume of liquid manure. Average Average Nitrogen Concentration is the average mass weight of nitrogen applied per volume of liquid manure. |
|
Instant Instant Ammonium is the instantaneous mass weight of ammonium applied per acre (or hectare) for the selected field. Average Average Ammonium is the average mass weight of ammonium applied per acre (or hectare) for the selected field. |
|
Instant Instant Ammonium Concentration is the instantaneous mass weight of ammonium applied per volume of liquid manure. Average Average Ammonium Concentration is the average mass weight of ammonium applied per volume of liquid manure. |
|
Instant Instant Phosphorus is the instantaneous mass weight of phosphorus applied per acre (or hectare) for the selected field. Average Average Phosphorus is the average mass weight of phosphorus applied per acre (or hectare) for the selected field. |
|
Instant Instant Phosphorus Concentration is the instantaneous mass weight of phosphorus applied per volume of liquid manure. Average Average Phosphorus Concentration is the average mass weight of phosphorus applied per volume of liquid manure. |
|
Instant Instant Potassium is the instantaneous mass weight of potassium applied per acre (or hectare) for the selected field. Average Average Potassium is the average mass weight of potassium applied per acre (or hectare) for the selected field. |
|
Instant Instant Potassium Concentration is the instantaneous mass weight of potassium applied per volume of liquid manure. Average Average Potassium Concentration is the average mass weight of potassium applied per volume of liquid manure. |
|
Instant Instant Dry Matter is the instantaneous percentage of manure slurry that is dry matter. Average Average Dry Matter is the average percentage of manure slurry that is dry matter. |
|
Instant Instant Volume is the instantaneous volume of manure slurry that is applied per acre (or hectare) for the selected field. Average Average Volume is the average volume of manure slurry that is applied per acre (or hectare) for the selected field. |
|
Total Volume is the total volume of manure slurry that has been applied for the current job. |
